Logo

P0016 Engine Trouble Code

P0016 Engine

When you check engine light came on code P0016 the reason should be . However your vehicle's manufacturer may have a different definition for the P0016 OBD-II Diagnostic Powertrain (P) Trouble Code. So you should chech it on our car models.

P0016 code can be about changing a broken oxygen sensor can lead to a busted catalytic convertor which can cost upwards of $1,300. Taking your vehicle into a service shop will cost you around $300 depending on the vehicle. But, an oxygen sensor is easy to replace on many vehicles and is detailed in the owner's manual PDF or in our website. If you know where this sensor is located, you only have to unclip the old oxygen sensor and replace it with a new sensor. Regardless of how you approach it, you should get this fixed right away.

P0016 Code Meaning :

P
OBD-II Diagnostic Powertrain (P) Trouble Code For Engine
0
Intake Valve Control Solenoid Circuit Low
0
Injector Circuit Malfunction - Cylinders
1
Ignition/Distributor Engine Speed Input Circuit Malfunction
6
Reverse Input Circuit

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

P0016 OBD-II Diagnostic Powertrain (P) Trouble Code Description

P0016 OBD-II Trouble Code Crankshaft Position Camshaft Position Correlation Bank 1 Sensor A is the generic definition for the P0016; however your vehicles manufacturer may have a different definition for the P0016 code. P0016 code. Injector Circuit Malfunction - Cylinders and Ignition/Distributor Engine Speed Input Circuit Malfunction causes most of code P0016.

Reason For P0016 Code

The reason of P0016 OBD-II Engine Trouble Code is Injector Circuit Malfunction - Cylinders.

P0016 DTC specifically refers to the camshaft (cam) timing. In this case, if the cam timing is over-retarded, the engine trouble light will be illluminated and the code will be set.

How To Repair P0016 Code

Before starting let's see P0016 repairing process steps:

  • Qualified technicians will begin by using a scan tool to access P0016 code stored in the ECU.
  • Technicians will note P0016 code present and any freeze frame data associated with them.
  • After all, if you sure the engine trouble is finished, the code will be cleared.

A faulty ECM could result in the vehicle to be dealing with a reduction in fuel efficiency, power, and acceleration. A vehicle that fails to start or struggles to start is another main symptom or a defective or failed ECM. If the ECM fails completely, the vehicle will remain with no engine control management, and will not be starting or running as a result.

P0016 code is stored again, the mechanic will perform a visual inspection of the pressure control solenoid and related systems. If any circuits or connections are damaged or loose, they will resolve these issues and move on to retest the system.

Sometimes P0016 code comes with P001600 code.

Diagnosis Of Engine Error OBD Code P0016

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a P0016 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the P0016 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.

All Engine Trouble Codes

All engine trouble codes with P, U, B and C engine codes.

Code Search

Please fill the "Code Box" to find engine fault code.

Example: 0140

Car Models :

Please select your car.

How To Read Engine Codes ?

Ways to read engine trouble codes.

How To Clear Check Engine Lights ?

Ways to clear check engine light on car panel.

Check Engine Light Dictionary

Ways to clear check engine light on car panel.